Home Hardening Video Series: Decks
Your deck is susceptible to ignition by embers and/or direct flame. As an extension of your home, it can provide a path by which flames can reach the structure.
Decks & Fire Safety
Summertime often means cookouts on the deck and gatherings with friends. But did you know that choosing the right kind of materials to build your deck and keeping it clear of combustible materials (both on the top and underneath) are critical steps in reducing the risk of a wildfire damaging your home?
Use your deck for entertaining, but remember – when a wildfire threatens, move combustible deck furniture and cushions inside or move as far away from the house as possible. Treat other combustible items, such as a broom, as your furniture and move them inside or far away from the house. Any LP tank for a grill should be moved off the deck and away from the home.
Maximize Fire Safety for Your Deck
• Firewood Improperly Stored Beneath a Decks your home located on a steep slope? If your deck overhangs a steep slope, be sure your defensible space is sufficient to minimize flames spreading up the hill. Consider building a noncombustible wall across the slope approximately 15–20 feet from the edge of the deck.
• Do you have materials stored under the deck? Do not store combustible materials under your deck. If you have no other option, installing a noncombustible siding product around the deck perimeter may be an option. Be sure the enclosed space is adequately ventilated to minimize the chance of water-related damage.
• Are the materials used to build your deck combustible? Most deck boards are combustible, including wood, plastic and wood-plastic composites. Solid surface decks, such as those made from lightweight concrete, are usually noncombustible, but are also more expensive. If you live in a wildfire-prone area anywhere in the country, when it’s time to replace deck boards, choose a product that complies with the requirements of the California Building Code, as provided in the Office of the State Fire Marshal Wildland Urban Interface Handbook.
• Has debris accumulated between deck boards? Regularly clean out debris from between deck board joints and other areas where debris has accumulated. Check the condition of wood deck boards and structural support members–replace or repair rotted members.
The vulnerability of decks to wildfire will depend on the decking board material, any combustible materials stored under the deck or kept on the deck, and the topography and amount and condition of vegetation leading to the deck. Even though noncombustible decking products are available (e.g., metal decking and lightweight concrete), many decking products are combustible. Untreated wood and wood treated with fire retardant, as well as plastic and wood-plastic composite products, are all combustible and therefore vulnerable to ember and other wildfire exposures. However, the deck can be designed to minimize exposure to embers. During fire season an important job will be to keep your deck free of easily ignited materials such as leaves and needles that have accumulated in the gaps between deck boards and at the interface between the deck and the siding of the house. Metal flashing can be applied to the lower 18 inches of the wall to protect combustible siding from the embers that may accumulate during a wildfire. It is important that the metal flashing be tucked in behind the lap-joint where it terminates. Decayed wood (rotted wood) is more readily ignited, so periodically inspect for decayed members and replace them.
Regardless of what type of deck board is used, ignition can occur from an accumulation of combustible material (grass, leaves, needles) under the deck. Embers can readily ignite this debris during a fire. Enclosing the underside of the deck is one method to reduce the risk of ignition. There are two ways to enclose your deck. You can enclose it by applying sheathing or siding around the perimeter (a vertical enclosure), or by attaching sheathing/panel materials to the underside of the structural support members (a horizontal enclosure). The more careful you are about not storing combustible materials near your home (and under your deck), maintaining near-home vegetation, and cleaning up windblown debris, the less important enclosing your deck becomes.
The closer the deck is to the ground, the harder it is to use as a storage area, but it also becomes more difficult to clean out debris that will accumulate. If you have a solid surface deck (e.g., one with a lightweight concrete walking surface), it is probably already enclosed horizontally. If you are going to store combustible materials under your deck, then vertically enclosing it with a noncombustible or ignition-resistant material would make sense. If you do this, make sure you avoid any potential moisture-related degradation issues by providing adequate venting or take other moisture control actions
Deck enclosure will not guard against embers falling on top of the deck, so be aware of combustible material that you have on your deck. Firewood should be moved off of the deck during wildfire season. Combustible materials commonly found on decks (e.g., brooms, umbrellas, patio furniture, door mats, etc.) should be moved off the deck if possible, or moved as far from the building as possible during wildfires and spaced to avoid clustering items.
Protecting Decks, Patios, and Porches
1.) Are the materials used to construct the deck, patio or porch combustible?
• Examples of combustible materials include solid wood or wood plastic composite products.
• Some manufacturers are now incorporating fire retardant chemicals into their products, and fire performance information for many decking products is now available on the manufacturer’s website.
• Wood decking treated with an exterior fire retardant also is available.
2.) Do you have combustible materials stored under or on top of the area?
3.) Is nearby vegetation well maintained?
4.) Combustible materials and vegetation can act as a wick and allow the fire to move to the deck and other building materials, igniting it and other items stored underneath or nearby.
5.) This is particularly important for decks when the house or business is sited on a sloped lot.
6.) Depending on the type and condition of the vegetation, flame lengths on a slope can reach more than 30 feet, so even an elevated deck can be vulnerable.
Steps to reduce the risk of wildfire damage:
Enclosing an elevated deck, patio or porch:
• To determine if enclosing your deck, patio or porch would be beneficial, consider whether you store combustible materials underneath it, or if your vegetation management plan is inadequate, particularly in the 0- to 30-foot zone.
• Avoid storing flammable materials on top of or beneath the deck.
• Providing sufficient ventilation or other means for water to drain out is a critical step in the enclosure process.
• The national building code standard requirement for a crawlspace is one square foot of venting for each 150 square feet of floor area. Allow at least this much ventilation and maybe more if you are in a particularly wet area. If you do not allow any wood or wood-based structural support members and boards to dry out, fungal decay will become the biggest threat to your deck, patio or porch.
• Enclosing your deck, patio or porch will not reduce the risk of the top being exposed to embers. For that, the best protection is to keep the surface clear of leaves, pine needles and other vegetative debris.
• If the house is supported by a column and beam system, and it doesn’t have skirting around the perimeter, add a skirting of a noncombustible material.
• Remember to provide vents on all sides to ensure proper ventilation. California’s Building Code has taken the lead in developing guidance for wildfire protections.
• Attaching a metal flashing strip, approximately 18 inches tall, between the top of the deck, patio or porch and the exterior (combustible) siding can create a barrier between exposure to burning debris ignited by embers and flames near the point where the house intersects with the deck, patio or porch.
• When attaching the flashing, make sure it is tucked in behind the siding where the top of flashing terminates. This will help prevent water from seeping between the flashing and the siding.
• Alternatively, if you can find a noncombustible siding material with a similar pattern, the lower two or three courses of siding could be replaced.
More important technical information about deck safety can be found at https://ucanr.edu/sites/fire/Prepare/Building/Deck/